Verona LED Grow Light 400W

The Verona LED Grow Light from IHS has been designed for easy installation in greenhouses. The lightweight design incorporates an integrated heatsink for optimal thermal management. Additionally, the inline connectors allow for easy connection to a LED driver. An emphasis on the red and far red ranges ensures quality and quantity of flowering yields. With a peak wavelength of 455nm, the Verona LED Grow Light is designed to provide beneficial photomorphogenic responses by creating a mild stress response in plants.

The Verona LED recipe has been developed to induce and encourage flowering using a significant content of far red light. The spectra has been designed to complement a growing environment where there is already available daylight. We are assuming the end application gets enough good quality daylight; thus, the Verona provides increases in critical wavelengths. The most important factor influencing flowering is day length, the use of the Verona LED Grow Light extends these key daylight hours.

With a built-in lens giving a 140×110 degree coverage, large areas of target plants can be illuminated with a single Verona LED Grow Light. With a 100-240VAC mains input that can be installed by any standard electrician, no complicated wiring or installation processes are required. With hanging hooks included, and a weight of only 4.9kg, installation is very simple in any application. Each Verona LED Grow Light is fitted with an IP65 connector which allows for easy connection.

Download Datasheet

Download Installation Manual

Download Flyer

Buy at RS

Buy at Amazon

Product Code: VERONA-400W-UK Categories: ,


  • Horticultural lighting
  • Indoor farming
  • Large greenhouses
  • Nurseries
  • Indoor home growing
  • Schools and universities
  • Research institutes




System efficacy

2.6 umol/J @ 220Vac

PPF Output

1040 umol/s

Current Range

3.33A @ 120V , 1.44 @ 277V

Isolation Class

Class I

Input Voltage

120-277Vac, 120-240Vac, 50-60Hz

Heat BTU Generated


Power Factor




Beam angle





Hanging hooks

Type of Protection



4.9 kg




5 years


340 x 260 x 79mm

Operating Temperature

0°C to 40°C

Storage Temperature

-40°C to 70°C


Supplied with each Verona LED Grow Light are the following accessories.

Hanging hooks and mains input cable.

Spectral Characteristics Calculations Explained

Below you will find specific photometric information for VERONA-400W-UK. This includes:

  • Spectral power
  • Spectral output
  • Spectral distribution patterns.

These three sets of spectral measurements have been obtained by testing a standard production unit, rather than a ‘special’ engineering unit. All readings were carried out in IHS’s in-house test facility in order to provide real life values that you can use in your own calculations.

The Verona LED Grow Light was suspended using the hanging hooks and powered according to our Verona installation manual.

The height of the unit was then varied so the front face of Verona, that is at lens level, was measured to the sensor level at varying increments: 300, 450, 600 and 900mm.

The unit was powered and left switched on for 2 hours before readings were taken to ensure thermal stability within the product had been achieved. Ambient temperature stood at approximately 20°C, whereby the average heatsink temperature increase was noted to be 50°C after stabilisation.

The spectral output graph below shows the percentage in flux for each wavelength. For example, if 660nm shows 90% and 455nm shows 10%, then you know the ratio of 600nm to 455nm is 2:1.

The spectral power illustration below represents the umol/m2/s reading taken at the central point at each of the varying heights. This value corresponds to a reading area of 150mm2.

The spectral distribution patterns provided below for each of the varying heights show the total umol/m2/s readings taken at 150mm intervals. If you look at the central value, the number either side depicts the umol/m2/s reading 150mm further out from the centre.

So a 0.45m2 area is shown on the chart as 3×3 squares.

Spectral Output

Spectral Power

Spectral Power and Distribution Patterns

Technical Drawing

Important Precautions

  • The LED module when powered up, are very bright. Thus it is advised that you do not look directly at them. Turn the LED module away from you and do not shine into the eyes of others.

  • LED modules, when operated, can reach high temperatures thus there is a risk of injury if they are touched.

  • DO NOT TOUCH or PUSH on the LED as this can cause irreparable damage.


Safety Information

  • The LED module itself and all its components must not be mechanically stressed.

  • Assembly must not damage or destroy conducting paths on the circuit board.

  • To avoid mechanical damage to the connecting cables, the boards should be attached securely to the intended substrate. Heavy vibration should be avoided.

  • Observe correct polarity! Depending on the product, incorrect polarity will lead to emission of red or no light. The module can be destroyed!

  • Pay attention to standard ESD precautions when installing the LED module.

  • Damage by corrosion will not be accepted as a materials defect claim. It is the user’s responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements.

  • For outdoor usage, a housing is definitely required to protect the board against environmental influences. The design of the housing must correspond to the IP standards in the application. It is also the responsibility of the user to ensure any housings or modifications keep the Tc junction temperature to within stated ranges.

  • To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. In Europe the declarations of conformity must include the following standards: CE: EC 61374-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 – ENEC: 61374-2-13 and IEC/EN 62384.

  • The evaluation of eye safety occurs according to the standard IEC 62471:2006 (“photobiological safety of lamps and lamp systems”). Within the risk grouping system of this CIE standard, the LED specified in this data sheet falls into the class “moderate risk” (exposure time 0.25s). Under real circumstances (for exposure time, eye pupils, observation distance), it is assumed that no endangerment to the eye exists from these devices. As a matter of principle, however, it should be mentioned that intense light sources have a high secondary exposure potential due to their blinding effect. As is also true when viewing other bright light sources (e.g. headlights), temporary reduction in visual acuity and afterimages can occur, leading to irritation, annoyance, visual impairment and even accidents, depending on the situation.

Installation and Mounting

For details about the installation and mounting of the Verona LED Grow Lights please refer to our documentation.

Verona LED Grow Light – Installation Manual

Latest News

20th March 2024

Now available for purchase in Distrelec for EU customers

Our IHS Ready to Grow lights are now available for quick and easy purchase through Distrelec. The Treviso, Trento and Siena LED grow lights are... Read More

13th December 2023

Tips to care for your Christmas Poinsettia from IHS

Poinsettia plants have become a key sign of the festive Christmas period, with their indistinguishable dark green leaves and red flowers that bloom though November-February.... Read More

Sign up for Updates

Contact Us

Intelligent Horticultural Solutions (IHS)

Unit 2, Berkshire Business Centre

Berkshire Drive, Thatcham

RG19 4EW, UK


Tel: +44 (0)1635 294606

IHS is a division of Intelligent Group Solutions Ltd. © IGS 2024 All rights reserved